313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 embedded power for business-critical continuity nfs110 medical series single and quad output special features 7.0 x 4.25 x 1.8 inch package medical, dental and laboratory applications overvoltage and short circuit protection 110 w with 20 cfm ul, vde and csa safety approvals en60601-1 and ul2601 medical approvals available rohs compliant 2 year warranty ? ? ? ? ? ? ? ? total power: 80 - 110 w input voltage: 90 - 253 vac 127 - 357 vdc # of outputs: single, quad safety vde0805/en60601-1/ iec601/iec1010 file no. 10401-3336-1049 licence no. 2874 ul2601 file no. e147937 csa c22.2 no. 125 file no. lr41062c ? ? ? ? ? ? ? rev. 12.29.08_139 nfs110-m series 1 of 5 electrical specifcations all specifcations are typical at nominal input, full load at 25 c unless otherwise stated output voltage adjustability: +5.1 v o/p on multi-s 5.1 v single output 12 v single output 15 v single output 24 v single output 3.0% 3.0% 12-14 v 15-18 v 24-30 v line regulation: ll to hl, fl all outputs on all units 0.1% max. overshoot/undershoot: at turn-on no lead 0% temperature coeffcient: all outputs 0.02% / c overvoltage protection: multi o/p 5.1 v only 5.1 v single 12 v single 15 v single 24 v single 6.25 v 0.75 v 6.25 v 0.75 v 15.75 v 1.0 v 22 v 1.5 v 33 v 2.5 v output power limit: primary power limited pin max. 160 w pout min. 110 w short circuit protection: burst mode operation input input voltage range: 90-253 vac 127-357 vdc input frequency range: 47-440 hz input surge current: 110 vac. 50 hz 230 vac. 50 hz 17 a 25 a safety ground leakage current: 132 vac 264 vac 50 a 100 a
rev. 12.29.08_139 nfs110-m series 2 of 5 embedded power for business-critical continuity 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 environmental specifcations thermal performance: operating, see curve 0 c to +70 c (see notes 9, 10) non-operating -40 c to +85 c 0 c to 50 c amb. convection cooled 80 w +50 c to +70 c, amb. convection cooled derate 2 w/c 0 c to +50 c, 20 cfm forced air 110 w +50 c to +70 c, 20cfm forced air derate 2.75 w/c peak, 0 c to +50 c, max. 60 seconds 110w relative humidity: non-condensing 5% to 95% rh altitude: operating 10,000 feet max. non-operating 40,000 feet max. vibration (see note 11): 5-500 hz 2.4 g rms peak emc characteristics conducted emissions: en55022, fcc part 15 level a radiated emissions: en55022, fcc part 15 level a esd air: en61000-4-2, level 3 perf. criteria 1 esd contact: en61000-4-2, level 4 perf. criteria 1 surge: en61000-4-3, level 3 perf. criteria 1 fast transients: en61000-4-4, level 3 perf. criteria 1 radiated immunity: en61000-4-5, level 3 perf. criteria 2 conducted immunity: en61000-4-6, level 3 perf. criteria 2 general specifcations hold-up time: 110 vac @ 80 w 110 vac @ 110 w 230 vac @ 80 w 230 vac @ 110 w 35 ms 17 ms 140 ms 100 ms effciency: multiple outputs +5.1 v single 12 v and 15 v singles 24 v single 70% typical 70% typical 72% typical 75% typical isolation voltage: input/output input/chassis 4000 vac 1500 vac approvals and standards: (see note 12) vde0750, iec60601, iec1010, ul2601, csa c22.2 no. 125 weight: singles multiple outputs 550 g (19.4 oz) 600 g (21.2 oz) mtbf (@25 o c) mil-hdbk-217e 125,000 hours min.
rev. 12.29.08_139 nfs110-m series 3 of 5 embedded power for business-critical continuity 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 notes 1 convection cooled, 80 w maximum. 2 peak outputs lasting less than 60 seconds with duty cycle less than 10%. total peak power must not exceed 110 w. 3 forced air, 20 cfm at 1 atmosphere, 110 w maximum. 4 figure is peak-to-peak. output ripple is measured across a 50 mhz bandwidth using a 12 inch twisted pair terminated with a 47 f capacitor. 5 total regulation is defned at the static output regulation at 25 c, including initial tolerance, line voltage within stated limits and output voltages adjusted to their factory settings. also for nfs110-7902pj, for 24 v output stated regulation i a / i b 2 5. this output will maintain 5.0% regulation if i a 2 5 a, where i a = +5.1 v output current and i b = +24 v output current. 6 single output models have foating outputs which may be referenced as either positive or negative. higher voltage supplies, may be adjusted over a wide output voltage range, as long as the total output power does not exceed 80 watts (natural convection) or 110 watts (forced air). 7 power fail detect not available on single output models. 8 derating curve is application specifc for ambient temperatures > 50 c, for optimum reliability no part of the heatsink should exceed 90 c and no semiconductor case temperature should exceed 100 c. 9 caution: allow a minimum of 1 second after disconnecting the power when making thermal measurements. 10 the user should read the psu installation instructions in conjunction with the relevant national safety regulations in order to ensure compliance. 11 three orthogonal axes, random vibration, 10 minute test for each axis. 12 this product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. 13 the j- suffx indicates that these parts are pb-free (rohs 6/6) compliant. tse rohs 5/6 (non pb-free) compliant versions may be available on special request, please contact your local sales representative for details. 14 notice: some models do not support all options. please contact your local emerson network power representative or use the on-line model number search tool at http://www.powerconversion.com to fnd a suitable alternative. emc characteristics output voltage output currents ripple (4) total regulation (5) m odel nu??ers odel nu ??ers (13, 14, f) max (1) peak (2) fan (3) +5.1 v 8 a 20 a 10 a 50 mv 2.0% NFS110-7901PJ +12 v 4.5 a 9 a 5 a 120 mv 3.0% C12 v 0.5 a 1.5 a 1 a 120 mv 3.0% C5 v 0.5 a 1.5 a 1 a 50 mv 3.0% +5.1 v (i a ) 8 a 20 a 10 a 50 mv 2.0% nfs110-7902pj +24 v (i b ) (6) 3.5 a 4.5 a 4.5 a 240 mv +10/C5.0% +12 v 4.5 a 9 a 5 a 120 mv 3.0% C12 v 0.5 a 1.5 a 1 a 120 mv 3.0% 12 v 7 a 9 a 9 a 120 mv 2.0% nfs110-7912j (7,8) 15 v 5 a 7.3 a 7.3 a 150 mv 2.0% nfs110-7915j (7,8) 24 v 3.5 a 4.5 a 4.5 a 240 mv 2.0% nfs110-7924j (7,8) transient response NFS110-7901PJ +5.1 v (7.5-10 a) 150 mv peak, 1 ms recovery +12 v (2.5-5 a) 100 mv peak, 0.5 ms recovery -12 v (0.5-1 a) 100 mv peak, 0.5 ms recovery -5 v (0.5-1 a) 100 mv peak, 0.5 ms recovery nfs110-7902pj +5.1 v (7.5-10 a) 150 mv peak, 1 ms recovery +12 v (2.5-5 a) 100 mv peak, 0.5 ms recovery -12 v (0.5-1 a) 100 mv peak, 0.5 ms recovery 24 v (1.5-3 a) 300 mv peak,1 ms recovery nfs110-7905j +5.1 v (10-20 a) 250 mv peak, 1 ms recovery nfs110-7912j +12 v (4.5-9 a) 360 mv peak, 1 ms recovery nfs110-7915j +15 v (3.65-7.3 a) 450 mv peak, 1 ms recovery nfs110-7924j +24 v (2.25-4.5 a 720 mv peak, 1 ms recovery
rev. 12.29.08_139 nfs110-m series of 5 embedded power for business-critical continuity 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 ac (j1) mating connector molex 09-50-3051 or molex 09-91-0500 mating connector with 2478 or equivalent crimp terminals. dc (j2) mating connector molex 09-50-3131 or molex 09-91-1300 mating connector with 2478 or equivalent crimp terminals. all dimensions in inches (mm) optional powe r fail de tect circuit (key = pin 2) pin 1 6-32 unc (4pl) pin 1 1.00 0.005 (25.4) voltage adjust j2 j1 f1 l1 t1 c6 pin 1 0.156 dia . hole (4pl) 5a, 250 vac 0.475 0.010 (12.07) 1.55 0.005 (39.37) 3.35 0.015 (85.09) 1.80 (45.72) max 0.050 0.020 (1.27) 4.250 0.020 (107.95) 3.750 0.005 (95.25) 0.250 0.010 (6.35) 0.250 0.010 (6.35) 6.50 0.005 (165.1) 7.00 0.020 (177.8) t1 power fail detect signal (note 8) 50ms t1 200ms t2 will vary with line and load t3 3ms pout: 110w pfd output is an open collector which will sink 40ma in the low state. hig h t1 t2 t3 4.75v 3.5v min 0-0.4 max low 4.75v 5v output pfd signal ac input optional power f ail detect timing diagram 80w 20 cfm forced air cooling 40w 55w 0w 11w 11w minimum load required at 230vac na tural convection cooling 0c 10c 20c 30c 40c 50c 60c 70c dera ting curve (see notes 9, 10) output powe r (watts) 110w n/c = no connection. pin connections j1 -7901pj -7902pj singles pin 1 ac ground ac ground ac ground pin 2 ac neutral ac neutral ac neutral pin 3 ac line ac line ac line j2 pin 1 +5.1 v +5.1 v v out pin 2 +5.1 v +5.1 v v out pin 3 +5.1 v +5.1 v v out pin 4 return return return pin 5 return return return pin 6 return return return pin 7 return return return pin 8 +12 v +12 v v out pin 9 +12 v +12 v v out pin 10 pfd pfd n/c pin 11 -12 v -12 v n/c pin 12 removed for key pin 13 -5 v +24 v n/c mechanical notes a metallic or non-metallic stand-offs (maximum diameter 5.4mm) can be used in all four mounting holes without effecting safety approval. b the ground pad of the mounting hole near j1, allows system grounding through a metal stand-off to the system chassis. c the heat sink is grounded, and allows system grounding by mechanical connection to the system chassis. d the supply must be mechanically supported using the pcb mounting holes and may be additionally supported by the heatsink mounting holes. e it is always advisable to attach the power supply heat sink to another thermal dissipator (such as a chassis or fnned heatsink etc). the resulting decrease in heat sink mounted component temperatures will improve power supply lifetime. f a standard l-bracket and cover is available for mounting which contains all screws, connectors and necessary mounting hardware. the kit is available, order part number nfs110cj.
313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 embedded power for business-critical continuity rev. 12.29.08_139 nfs110-m series 5 of 5 a?ericas 5810 van allen way carlsbad, ca 92008 usa telephone: +1 760 930 4600 facsimile: +1 760 930 0698 europe (uk) waterfront business park merry hill, dudley west midlands, dy5 1lx united kingdom telephone: +44 (0) 1384 842 211 facsimile: +44 (0) 1384 843 355 asia (hk) 14/f, lu plaza 2 wing yip street kwun tong, kowloon hong kong telephone: +852 2176 3333 facsimile: +852 2176 3888 for global contact, visit: www.powerconversion.co? techsupport.e??eddedpower @e?erson.co? while every precaution has been taken to ensure accuracy and completeness in this literature, emerson network power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. emerson network power and the emerson network power logo are trademarks and service marks of emerson electric co. ?2008 emerson electric co. e?ersonnetworkpower.co? embedded computing e?? edded power monitoring outside plant power switching & controls precision cooling racks & integrated cabinets services surge protection e? erson network power. the global leader in enabling business-critical continuity. ac power connectivity dc power
|
